总裁俱乐部app

OBD Codes
Your OBD-II Trouble Codes Repair Site

P2247 O2 Sensor Reference Voltage Circuit/Open Bank 2 Sensor 1

OBD-II Trouble Code Technical Description

Article by
Stephen Darby
Stephen Darby
ASE Certified Technician

总裁俱乐部appO2 Sensor Reference Voltage Circuit/Open Bank 2 Sensor 1

What does P2247 mean?

This diagnostic trouble code (DTC) is a generic powertrain code and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Honda, Ford, Mazda, VW, Mercedes-Benz, Audi, Hyundai, Acura, BMW, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.


 

总裁俱乐部appA stored code P2247 means that the powertrain control module (PCM) has detected an open reference voltage circuit for the upstream O2 sensor for engine bank two Sensor 1 refers to an upstream sensor and Bank 2 refers to the bank of the engine which does not contain the number one cylinder.

The engine air to fuel ratio for each engine bank is monitored by the PCM using data input from heated exhaust oxygen sensors. Each oxygen sensor is constructed using a zirconium dioxide sensing element situated in the center of a vented steel housing. Tiny electrodes (usually of platinum) attach the sensing element to wire leads in the oxygen sensor harness connector and the connector plugs into the controller area network (CAN) which connects the oxygen sensor wiring harness to the PCM connector.

总裁俱乐部appEach oxygen sensor is threaded (or studded) into an exhaust pipe. It is situated so that the sensing element is near the center of the pipe. As spent exhaust gases exit the combustion chamber (via the exhaust manifold) and continue through the exhaust system (including catalytic converters), they flow over the oxygen sensors. Exhaust gases enter the oxygen sensor through specially designed vent holes in the steel housing and swirl around the sensing element. Swirling ambient air is drawn through wire lead cavities in the sensor housing where they fill a tiny chamber in the middle. The air (in the tiny chamber) is then heated. This forces the oxygen ions to produce energy that is recognized by the PCM as voltage.

Variations between the number of oxygen ions in ambient air (drawn into the O2 sensor), and the number of oxygen molecules in the exhaust, cause the oxygen ions inside the O2 sensor to bounce from one platinum layer to the other, very swiftly and repetitively. As the surging oxygen ions shift between platinum layers, variations in oxygen sensor output voltage occur. The PCM sees these variations in oxygen sensor output voltage as changes in exhaust oxygen concentration. Voltage signal outputs from the oxygen sensors are lower when more oxygen is present in the exhaust (lean condition) and higher when less oxygen is present in the exhaust (rich condition).

If the PCM detects an open circuit in oxygen sensor reference voltage, a code P2247 will be stored and a malfunction indicator lamp (MIL) may be illuminated. Most vehicles will require multiple ignition cycles (with a failure) for MIL illumination.

A typical oxygen O2 sensor:
P2247 A Typical Oxygen O2 Sensor:

What is the severity of this DTC?

An open O2 sensor reference voltage circuit may lead to diminished fuel efficiency and a reduction in engine performance. A code P2247 should be categorized as severe and rectified as quickly as possible.

What are some of the symptoms of the code?

总裁俱乐部appSymptoms of a P2247 trouble code may include:

What are some of the common causes of the code?

Causes for this code may include:

What are some P2247 troubleshooting steps?

You will need a diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of reliable vehicle information in order to accurately diagnose a code P2247.

You may save yourself time by searching for technical service bulletins (TSB) that replicate the code stored, vehicle (year, make, model, and engine), and symptoms exhibited. This information may be found in your vehicle information source. If you find the right TSB, it could yield a speedy solution to your diagnosis.

After you connect the scanner to the vehicle diagnostic port and retrieve all stored codes and pertinent freeze frame data, write the information down (in case the code proves to be an intermittent one). After that, clear the codes and test drive the vehicle until one of two things happens; the code is restored or the PCM enters readiness mode.

总裁俱乐部appThe code may be more difficult to diagnose if the PCM enters readiness mode at this point, because the code is intermittent. The condition which caused the P2247 to be stored may need to worsen before an accurate diagnosis can be made. If the code is restored, continue with the diagnosis.

总裁俱乐部appYou may obtain connector face views, connector pinout charts, component locator charts, wiring diagrams, and diagnostic flow charts (pertaining to the code and vehicle in question) using your source of vehicle information.

Perform a visual inspection of related wiring and connectors. Repair or replace wiring that has been cut, burned, or damaged.

总裁俱乐部appUse the DVOM to test O2 sensor voltage at the appropriate connector pin (near the sensor). If no voltage is detected, check system fuses. Replace blown or otherwise defective fuses as required.

If voltage is detected, test the corresponding circuit at the PCM connector. If no voltage is detected there, suspect an open circuit between the sensor in question and the PCM. If voltage is discovered there, suspect a defective PCM or PCM programming error.

To test O2 sensors: Start the engine and allow it to reach normal operating temperature. Allow the engine to idle (with the transmission in neutral or park). With the scanner connected to the vehicle diagnostic port, observe oxygen sensor input data on the data stream. Narrow the scope of the data stream to include only pertinent data and you will get a faster response.

If the oxygen sensors are functioning normally, voltage on pre-cat oxygen sensors will cycle continuously between 1 and 900-millivolts once the PCM enters closed loop operation. Post-cat sensors will cycle between 1 and 900-millivolts as well but they will settle at a certain point and remain relatively stable) compared to the pre-cat sensors). Oxygen sensors which fail to cycle adequately should be considered defective if the engine is in good working order.

Related DTC Discussions

Need more help with a P2247 code?

If you still need help regarding the P2247 trouble code, please post your question in our FREE car repair forums.

总裁俱乐部appNOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.

手机棋牌输了几百万 我爱彩票邀请码是多少 怎么购买手机赌博软件 怎么样进入赌单双软件 快钱彩票官网 怎么下载波克棋牌 手机版彩票过滤工具 快乐棋牌游戏 我想查查彩票开奖结果 怎样买世界杯足球彩票