总裁俱乐部app

OBD Codes
Your OBD-II Trouble Codes Repair Site

P202C Reductant Tank Heater Control Circuit High

OBD-II Trouble Code Technical Description

Article by
Stephen Darby
Stephen Darby
ASE Certified Technician

Reductant Tank Heater Control Circuit High

What does that mean?

This diagnostic trouble code (DTC) is a generic powertrain code and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Volkswagen, Mercedes-Benz, Dodge, Audi, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.


 

A stored code P202C means that the powertrain control module (PCM) has detected excessive voltage in the control circuit for the reductant tank heater.

The catalyst system is responsible for reduction of (basically) all exhaust emissions although certain applications are also equipped with a NOx trap.

Exhaust gas recirculation (EGR) systems go another step further in the reduction of NOx. Nevertheless, today's larger and more powerful diesel engines cannot meet strict federal (U.S.) emission standards with the EGR, diesel particulate filter/catalytic converter, and NOx trap alone. It was for this reason that selective catalytic reduction (SCR) systems were invented.

总裁俱乐部appSCR systems inject a reductant compound or a diesel exhaust fluid (DEF) into the exhaust in front of the diesel particulate filter, NOx trap, and/or the catalytic converter via the reductant injection valve (solenoid). The precisely timed DEF injection elevates the temperature of the filtration element and allows it to perform more efficiently. It enhances filtration element longevity and allows fewer harmful exhaust emissions to be released into the atmosphere. The entire SCR system is monitored and controlled by either the PCM or a stand-alone controller (which interacts with the PCM). Either way, the controller monitors the O2, NOx, and exhaust temperature sensors (as well as other inputs) to determine the appropriate time for DEF (reductant) injection. Precise DEF injection is necessary to maintain exhaust temperature within acceptable parameters and optimize pollutant filtration.

总裁俱乐部appReductant tank heaters are used to prevent diesel exhaust fluid from freezing during extreme cold temperatures. These heaters are typically located in or around the DEF reservoir.

总裁俱乐部appIf the PCM detects a level of voltage on the reductant tank heater control circuit that is higher than the maximum allowable parameter, a code P202C will be stored and a malfunction indicator lamp (MIL) may be illuminated. Multiple ignition cycles - with a failure - may be required for MIL illumination.


P202C

What is the severity of this DTC?

A stored code P202C should be considered severe and addressed as quickly as possible. The SCR system could be disabled because of it. Catalyst damage could result if the conditions which contributed to the code being stored are not rectified in a timely fashion.

What are some of the symptoms of the code?

总裁俱乐部appSymptoms of a P202C trouble code may include:

What are some of the common causes of the code?

Causes for this code may include:

What are some P202C troubleshooting steps?

A diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of vehicle specific diagnostic information will be required to diagnose a code P202C.

You may use your source of vehicle information to locate a technical service bulletin (TSB) that matches the vehicle year, make, and model; as well as the engine size, code/s stored, and symptoms exhibited. If you find one, it could yield helpful diagnostic information.

Use the scanner (connected to the vehicle diagnostic connector) to retrieve all stored codes and pertinent freeze frame data. It is a good idea to write this information down before clearing the codes then test-drive the vehicle until the PCM either enters readiness mode or the code is reset.

If the PCM enters readiness mode at this time, the code is intermittent and may be much more difficult to diagnose. If this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made.

If the code is immediately reset, the next step of your diagnosis will require that you search your vehicle information source for diagnostic flow-charts, connector pin-out charts, connector face views, and component testing procedures/specifications.

Step 1

Use the DVOM to test the reductant tank heater element according to manufacturer specifications. Heaters are typically of the blanket or pin variety. Heater elements which do not test within maximum allowable parameters should be considered defective.

Step 2

总裁俱乐部appUse your source of vehicle diagnostic information and the DVOM to test reductant heater circuit voltage (usually battery voltage) with the system activated. If current conditions won’t permit activation, use the scanner to manually activate the heater.

Step 3

总裁俱乐部appIf the reductant tank heater is functional, use the DVOM to test input and output signal circuits from the fuse panel, PCM, and ignition switch. Disconnect all controllers prior to using the DVOM for testing.

Related DTC Discussions

Need more help with a P202C code?

If you still need help regarding the P202C trouble code, please post your question in our FREE car repair forums.

总裁俱乐部appNOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.

手机棋牌输了几百万 我爱彩票邀请码是多少 怎么购买手机赌博软件 怎么样进入赌单双软件 快钱彩票官网 怎么下载波克棋牌 手机版彩票过滤工具 快乐棋牌游戏 我想查查彩票开奖结果 怎样买世界杯足球彩票