总裁俱乐部app

OBD Codes
Your OBD-II Trouble Codes Repair Site

P0803 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction

OBD-II Trouble Code Technical Description

Article by
Stephen Darby
Stephen Darby
ASE Certified Technician

总裁俱乐部app1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction

What does that mean?

总裁俱乐部appThis diagnostic trouble code (DTC) is a generic powertrain code and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Chevrolet, Mercedes-Benz, BMW, Ford, GMC, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.


 

If your vehicle has stored a code P0803, it means that the powertrain control module (PCM) has detected a malfunction in the transmission upshift (also called skip shift) solenoid control system.

总裁俱乐部appThe automatic transmission upshift control solenoid is used in vehicle applications where the transmission may be manually shifted through the gear range by pushing or pulling the shift lever in a singular direction. This feature is especially popular in high-performance or sports cars. Since the shifter only needs to be moved slightly, an electronic solenoid is required to input a shift signal to the TCM and effect the desired gear change.

The transmission control module (TCM) may be stand alone unit but is most commonly integrated into a single housing with the engine control module (ECM). This is what is referred to as the PCM.

总裁俱乐部appIf the PCM detects a malfunction in the upshift solenoid control circuit, a code P0803 will be stored and a malfunction indicator lamp (MIL) illuminated


P0803

What is the severity of this DTC?

总裁俱乐部appA stored code P0803 indicates that an upshift solenoid control circuit malfunction has been detected. Since the upshift (or skip shift) system is an auxiliary or high-performance shifter feature, it is not a critical transmission control system and a code P0803 should not be classified as severe.

What are some of the symptoms of the code?

总裁俱乐部appSymptoms of a P0803 trouble code may include:

What are some of the common causes of the code?

总裁俱乐部appCauses for this code may include:

What are some P0803 troubleshooting steps?

When diagnosing automatic transmission codes, you should begin by making sure that the transmission fluid is clean and that the transmission if filled to the appropriate level. If the fluid level is low, locate the source of the leak and repair the condition. Refill the transmission with the recommended fluid and proceed.

If the fluid is excessively dark and smells strongly of burnt friction material, it will need to be replaced. This can be accomplished by removing the transmission pan (and draining the torque converter) or flushing the transmission (recommended). Either way, you will want to replace the filter at this time too. When removing the pan from the transmission, take care to preserve whatever debris may have landed therein. If the pan is relatively clear of debris you can assume that the clutches are mechanically intact. If there is an excessive amount of friction material in the pan (and stuck to the magnet), the transmission will require a rebuild from a qualified technician.

A diagnostic scanner, a digital volt/ohmmeter (DVOM), and a source of vehicle specific diagnostic information will be required to diagnose a code P0803.

总裁俱乐部appYou may use your source of vehicle information to locate a technical service bulletin (TSB) that matches the vehicle year, make, and model; as well as the engine size, code/s stored, and symptoms exhibited. If you find one, it could yield helpful diagnostic information.

总裁俱乐部appWith the transmission filled to the appropriate level with the recommended fluid, proceed with the first step of the diagnosis.

Step 1

总裁俱乐部appUse the scanner (connected to the vehicle diagnostic connector) to retrieve all stored codes and pertinent freeze frame data. It is a good idea to write this information down before clearing the codes then test-drive the vehicle until the PCM either enters readiness mode or the code is reset.

If the PCM enters readiness mode at this time, the code is intermittent and may be much more difficult to diagnose. If this is the case, the conditions which contributed to the code being stored may need to worsen before an accurate diagnosis can be made.

Step 2

总裁俱乐部appIf the code is immediately reset, the next step of your diagnosis will require that you search your vehicle information source for diagnostic flow-charts, connector pin-out charts, connector face views, and component testing procedures/specifications.

Step 3

Use the DVOM to test voltage and ground circuits at the skip shift solenoid. If voltage and ground are detected, use the DVOM to test the solenoid itself.

Step 4

If no skip shift components have failed, use the DVOM to test system circuits. The voltage drop testing method works well for this task. Disconnect all controllers from the circuit prior to testing resistance with the DVOM.

Related DTC Discussions

Need more help with a P0803 code?

If you still need help regarding the P0803 trouble code, please post your question in our FREE car repair forums.

总裁俱乐部appNOTE: This information is presented for information purposes only. It is not intended as repair advice and we are not responsible for any actions you take on any vehicle. All information on this site is copyright protected.

手机棋牌输了几百万 我爱彩票邀请码是多少 怎么购买手机赌博软件 怎么样进入赌单双软件 快钱彩票官网 怎么下载波克棋牌 手机版彩票过滤工具 快乐棋牌游戏 我想查查彩票开奖结果 怎样买世界杯足球彩票